A fast drying reputation isn’t all Intercure® HS is renowned for. Complete with MIO, this primer/intermediate can improve your productivity and lower your. Allow appropriate loss factors. Airless Spray, Air Spray, Brush, Roller. PRACTICAL. INFORMATION FOR. INTERCURE Colour. Gloss Level. Volume Solids. A fast drying reputation isn’t all International Intercure HS is renowned for. Complete with MIO, this Fast cure anti-corrosive primer/intermediate with added.
|Published (Last):||6 February 2007|
|PDF File Size:||3.61 Mb|
|ePub File Size:||18.8 Mb|
|Price:||Free* [*Free Regsitration Required]|
INTERCURE HS – SAND (KIT / 4G) – L
Each product clause is authored in NBS format and is intended for inclusion in project specifications. Inhercure compatibility Intercure HS will normally be applied to suitably prepared steel, e. VOC values are typical and are provided for guidance purpose only. At low temperatures, it may be necessary to thin Intercure HS to enable airless apray application to be performed. Other content by this manufacturer: Varnish Hybrid Water base.
This product is no longer in stock. The minimum purchase order nitercure for the product is 1. Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units.
International Intercure 200HS
Send us your question. Be the first to write a review for this product! The figures stated above are approximate. It can also be used as a primer for substrates other than blasted steel, e.
Suitable for overcoating within 7 hours in most climatic conditions hence speeding up production and throughput in fabrication infercure. Surface preparation All surfaces to be coated should be clean, dry and free from contamination. Provides quick cure even at low temperatures often encountered in maintenance painting.
Offers excellent barrier protection, low temperature cure and rapid overcoating properties. Warning Intercure HS is preferred for use with systems for chemical environments where zinc based materials can be subject to attack in both acidic and alkaline conditions. To find out more about producing specifications for building projects visit www.
However, if necessary, application over prefabrication blast primers can be performed. GTA Do not thin more than allowed by local environmental legislation Mix ratio: As a primer for steelwork intended for use in a wide range of environmental conditions including offshore, chemical and petrochemical plants, industrial buildings, pulp and paper mills, power plants and bridges.
The question has been correctly sent. Low trade prices Our best interure prices on everything!
Please ensure you refer to all datasheets for full application information. Suitable for overcoating hx 7 hours in most climatic conditions hence speeding up production and throughput in fabrication shops.
International Intercure HS – Rawlins Paints
020 The use of alternative thinners, particularly those containing ketones, can severely inhibit the curing mechanism of the coating. Customer agrees that before placing an Intercuree, Customer has read and understood the most up to date Product Data Sheet for the Product. Over-application of Intercure HS will extend both the minimum overcoating periods and handling times, and may be detrimental to long term overcoating properties. Intercure HS is not intended for use as a primer for steelwork which may be subjected to continuous immersion conditions.
This product is no longer in stock Red.
INTERCURE 200HS – SAND (KIT / 4G) – 11.36L
Provides quick cure even at low temperatures often encountered in maintenance painting. A fast drying reputation isn’t all International Intercure HS is renowned for.
Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. These may be subject to variation depending on factors such as differences in color and normal manufacturing tolerances. It is your responsibility to read the Product Data Sheets available below before you place an order and prior to application of the product. Additionally, in common with all epoxies Intercure HS will chalk on exterior exposure.
If oxidation has occurred between blasting and application of Intercure HS the surface should be reblasted to the specified visual standard. The surface may deteriorate to Sa2 standard but must be free from ijtercure powdery deposits.
Suitable for overcoating within seven hours in most climatic conditions. Press and move to zoom. Intercure HS is suitable for application to blast cleaned surfaces which were initially to the above standard but have been allowed to deteriorate under good shop conditions for up to days.
Not intended for use as a primer for steelwork which may be subjected to continuous immersion conditions. Surface defects revealed by the blast cleaning process should be ground, filled, or treated in the appropriate manner.